Washer repair in The Colony, TX
A washer that won't spin, won't drain, or floods the laundry room turns a simple load of laundry into a real headache. Our technicians carry the parts for the most common washer failures, so most repairs are finished in a single visit.
Signs your washer needs a repair
Most washer problems give some warning before they leave you with a load of wet laundry and no way to finish it. Here's what to watch for.
Won't spin
A drum that stays still or spins weakly usually points to a worn drive belt or a failing motor coupling.
Won't drain
Standing water left in the drum after a cycle is often a clogged pump filter or a blocked drain hose.
Loud banging or grinding
Noise during the spin cycle usually means worn drum bearings or a shock absorber that needs replacing.
Leaking water
Puddles near the machine often trace back to a damaged door gasket, loose hose, or worn tub seal.
Won't turn on or lock
A dead lid switch, door latch, or control board can keep the machine from starting a cycle at all.
Excessive vibration
A machine that shakes or walks across the floor points to worn suspension parts or a load balance sensor issue.
Common causes and what repairs typically cost
Here's what usually causes each washer problem we see in The Colony, and the typical price range once your technician confirms the exact issue.
| Likely cause | What it means | Typical repair cost* |
|---|---|---|
| Worn drive belt | Connects the motor to the drum — a common reason the tub stops spinning. | $100 – $200 |
| Clogged or failed drain pump | Pumps water out of the tub during the drain and spin cycles. | $150 – $350 |
| Faulty door lock or lid switch | A safety switch that must engage before the machine will run. | $90 – $200 |
| Bad water inlet valve | Controls water flow into the machine and can cause leaks when it fails. | $100 – $220 |
| Worn drum bearings or seal kit | Supports the spinning drum, often the source of loud grinding noise. | $200 – $350 |
| Failed control board | The circuit board that manages power to the washer's components. | $200 – $500 |
*Ranges reflect typical parts-and-labor costs across the industry. Your technician confirms the exact price on-site before starting any repair.
Repair or replace? Here's how to decide
A new washer typically costs $500 to $1,500 installed, so most single-part repairs are the cheaper option — unless your machine is older and already on its second or third repair.
- Under 10 years old with one failed part — usually worth repairing
- Repeated repairs within a year — replacement may cost less long-term
- Motor or transmission failure on an older unit — often the exception
- Not sure? Our technician gives you an honest recommendation on-site
How we repair your washer
Here's what happens from your first call to a working washer again.
Inspect & diagnose
We check the belt, pump, valves, and bearings to find the actual cause of the problem.
Quote before we start
You get a flat-rate price for the repair before we touch any parts.
Repair on the spot
Most parts are stocked on the truck, so the fix usually happens the same visit.
Run a full test cycle
We run a complete cycle to confirm the washer spins, drains, and fills correctly.
Brands we repair
We regularly service Whirlpool, Samsung, LG, GE, Maytag, and Bosch washers found throughout The Colony.
Related services
If your washer needs attention, your dryer is often next in line.
View all servicesWasher repair questions
What homeowners in The Colony most often ask before booking a washer repair.
Why won't my washer spin?+
The most likely causes are a worn or broken drive belt, a faulty motor coupling, or a lid switch or door latch that isn't engaging. An unbalanced load can also trigger the machine's safety sensors, so try redistributing the laundry first.
How much does washer repair cost?+
Most washer repairs run between $90 and $500 depending on the part, plus the standard $60–$95 service call fee. We confirm the exact price on-site before doing any work.
Why is my washer leaking water?+
Leaks are most often traced to a damaged door gasket, a loose hose connection, or a worn tub seal. Identifying exactly where the water is coming from during a cycle helps narrow down the cause quickly.
Is it worth repairing an older washer?+
If it's a single-part failure and the machine is under about 10 years old, repairing is usually cheaper than a new washer, which typically runs $500 to $1,500 installed. Frequent repairs or a failed motor on an older unit are signs it may be time to replace it.
How long does a washer repair take?+
Most repairs are completed in one visit, often within an hour, since our trucks carry the parts needed for the most common washer failures.
Is it safe to keep using my washer with a leak?+
We recommend turning off the water supply and avoiding use until it's repaired. A small leak can quickly turn into water damage to your flooring or the machine's electrical components.
Washer acting up? Let's get it fixed today.
Call now for a same-day or next-day appointment with a local technician.